{"id":75531,"date":"2024-10-17T17:10:06","date_gmt":"2024-10-17T17:10:06","guid":{"rendered":"https:\/\/pdfstandards.shop\/product\/uncategorized\/astm-a1031-3\/"},"modified":"2024-10-24T19:21:53","modified_gmt":"2024-10-24T19:21:53","slug":"astm-a1031-3","status":"publish","type":"product","link":"https:\/\/pdfstandards.shop\/product\/publishers\/astm\/astm-a1031-3\/","title":{"rendered":"ASTM-A1031"},"content":{"rendered":"

ASTM A1031\/A1031M-12<\/h3>\n

Historical Standard: Standard Specification for Steel, Sheet and Strip, Heavy-Thickness Coils, Alloy, Drawing Steel and Structural Steel, Hot-Rolled<\/h4>\n
\n

ASTM A1031\/A1031M<\/h4>\n

Scope<\/strong><\/p>\n

1.1 This specification covers hot-rolled, heavy thickness coils beyond the size limits of Specifications A506 and A507.<\/p>\n

1.2 The product is available in three designations: Alloy Steel, Drawing Steel, and Structural Alloy Steel.<\/p>\n

1.3 Alloy steel is furnished to chemical composition requirements and is intended primarily for general or miscellaneous use where bending and moderate forming is a requirement.<\/p>\n

1.4 Drawing steel is produced principally for applications involving severe cold plastic deformation such as deep drawn or severely formed parts.<\/p>\n

1.4.1 Drawing steel may be furnished in several conditions, heat treatments, surface finishes, and edges, as specified herein.<\/p>\n

1.5 Structural steel is furnished to chemical composition requirements and to specific mechanical property requirements which may include tension tests, hardness tests, or other commonly accepted mechanical tests.<\/p>\n

1.5.1 The formability of structural steel decreases with increasing yield strength or hardness. Therefore, product design in relation to the mechanical properties of the grade used must be considered.<\/p>\n

1.6 This material is available only in coils described as follows:<\/p>\n

1.7 Sheet and strip in coils of sizes noted in 1.6 are covered by this specification only with the following provisions:<\/p>\n

1.7.1 The material is not to be converted into steel plates for structural or pressure vessel use unless tested in complete accordance with the appropriate sections of Specifications A6\/A6M (plates provided from coils) or A20\/A20M (plates produced from coils). A plate produced in this manner is no longer governed by this sheet steel specification and since this material is now plate, the appropriate plate standard must now apply.<\/p>\n

1.7.2 The dimensional tolerances of Specification A635\/A635M are applicable to material produced to this specification.<\/p>\n

1.7.3 The material is to be fed directly from coils into a blanking press, drawing or forming operation, tube mill, rolling mill, or sheared or slit into blanks for subsequent drawing or forming.<\/p>\n

1.8 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.<\/p>\n

1.8.1 Within the text the SI units are shown in brackets.<\/p>\n

TABLE 1 Standard Steels Commonly Produced for Alloy Steel Sheet and Strip<\/p>\n

A<\/span><\/sup> The chemical ranges and limits shown are subject to product analysis tolerances. See Specification A505.<\/p>\n

B<\/span><\/sup> Other silicon ranges are available. Consult the producer.<\/p>\n

C<\/span><\/sup> Not an SAE Steel Designation.<\/p>\n

Keywords<\/strong><\/p>\n

alloy steel sheet; alloy steel strip; alloy structural steel; drawing steel; heavy-thickness coils; hot-rolled alloy steel; Drawing steel (DS) sheet\/strip–specifications; Heavy-thickness steel coils–specifications; Hot-rolled steel sheet\/strip–specifications; Steel sheet\/strip–structural<\/p>\n

ICS Code<\/strong><\/p>\n

ICS Number Code 77.140.50 (Flat steel products and semi-products)<\/p>\n

DOI:<\/strong> 10.1520\/A1031_A1031M-12<\/p>\n<\/div>\n

PDF Catalog<\/h4>\n\n\n\n\n\n\n
PDF Pages<\/th>\nPDF Title<\/th>\n<\/tr>\n
1<\/td>\nScope
Referenced Documents <\/td>\n<\/tr>\n
2<\/td>\nGeneral Requirements for Delivery
Ordering Information
TABLE 1 <\/td>\n<\/tr>\n
3<\/td>\nManufacture
Chemical Requirements
Metallurgical Structure
Mechanical Requirements
TABLE 2 <\/td>\n<\/tr>\n
4<\/td>\nWorkmanship, Finish and Appearance
Keywords <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":"

A1031\/A1031M-12 Standard Specification for Steel, Sheet and Strip, Heavy-Thickness Coils, Alloy, Drawing Steel and Structural Steel, Hot-Rolled<\/b><\/p>\n\n\n\n\n
Published By<\/td>\nPublication Date<\/td>\nNumber of Pages<\/td>\n<\/tr>\n
ASTM<\/b><\/a><\/td>\n2012<\/td>\n4<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n","protected":false},"featured_media":75532,"template":"","meta":{"rank_math_lock_modified_date":false,"ep_exclude_from_search":false},"product_cat":[1118,2637],"product_tag":[],"class_list":{"0":"post-75531","1":"product","2":"type-product","3":"status-publish","4":"has-post-thumbnail","6":"product_cat-77-140-50","7":"product_cat-astm","9":"first","10":"instock","11":"sold-individually","12":"shipping-taxable","13":"purchasable","14":"product-type-simple"},"_links":{"self":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product\/75531","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product"}],"about":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/types\/product"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/media\/75532"}],"wp:attachment":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/media?parent=75531"}],"wp:term":[{"taxonomy":"product_cat","embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product_cat?post=75531"},{"taxonomy":"product_tag","embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product_tag?post=75531"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}