25.100.25 – Tools for planing and broaching machines – PDF Standards Store ?u= Wed, 06 Nov 2024 01:48:52 +0000 en-US hourly 1 https://wordpress.org/?v=6.7.1 ?u=/wp-content/uploads/2024/11/cropped-icon-150x150.png 25.100.25 – Tools for planing and broaching machines – PDF Standards Store ?u= 32 32 JIS B 4239:1999/Amendment 1:2009 ?u=/product/publishers/jis/jis-b-42391999-amendment-12009/ Wed, 06 Nov 2024 01:48:52 +0000 Involute Spline Broaches (Amendment 1)
Published By Publication Date Number of Pages
JIS 2009-02-20 4
]]> Involute Spline Broaches (Amendment 1)
Published By Publication Date Number of Pages
JIS 2009-02-20 4
]]> JIS B 4239:1999 ?u=/product/publishers/jis/jis-b-42391999/ Wed, 06 Nov 2024 01:48:51 +0000 Involute Spline Broaches
Published By Publication Date Number of Pages
JIS 1999-12-20 16
]]> Involute Spline Broaches
Published By Publication Date Number of Pages
JIS 1999-12-20 16
]]> JIS B 4238:1999/Amendment 1:2009 ?u=/product/publishers/jis/jis-b-42381999-amendment-12009/ Wed, 06 Nov 2024 01:48:49 +0000 Keyway Broaches (Amendment 1)
Published By Publication Date Number of Pages
JIS 2009-02-20 4
]]> Keyway Broaches (Amendment 1)
Published By Publication Date Number of Pages
JIS 2009-02-20 4
]]> JIS B 4237:1987 ?u=/product/publishers/jis/jis-b-42371987/ Wed, 06 Nov 2024 01:48:48 +0000 Dimensions of Pull and Follower Ends of Broach
Published By Publication Date Number of Pages
JIS 1987-02-01 10
]]> Dimensions of Pull and Follower Ends of Broach
Published By Publication Date Number of Pages
JIS 1987-02-01 10
]]> JIS B 4238:1999 ?u=/product/publishers/jis/jis-b-42381999/ Wed, 06 Nov 2024 01:48:48 +0000 Keyway Broaches
Published By Publication Date Number of Pages
JIS 1999-12-20 9
]]> Keyway Broaches
Published By Publication Date Number of Pages
JIS 1999-12-20 9
]]> JIS B 0175:1996 ?u=/product/publishers/jis/jis-b-01751996/ Wed, 06 Nov 2024 01:42:31 +0000 Broaches - Vocabulary
Published By Publication Date Number of Pages
JIS 1996-12-20 47
]]> Broaches - Vocabulary
Published By Publication Date Number of Pages
JIS 1996-12-20 47
]]> ISO 241:1994 ?u=/product/publishers/iso/iso-2411994/ Tue, 05 Nov 2024 22:46:29 +0000 Shanks for turning and planing tools — Shapes and dimensions of the section
Published By Publication Date Number of Pages
ISO 1994-12 5
]]> Cancels and replaces the first edition (1975). Specifies the types and dimensions of the section of shanks for turning and planing tools of high speed steel and with brazed hardmetal tips. Specifies three types: round section; square section; rectangular sections with ratios of height to width of approximately 1,25; 1,6 and 2.

]]> CAN/CSA-E1029-2-3-94:1999 Edition ?u=/product/publishers/csa/can-csa-e1029-2-3-94/ Tue, 05 Nov 2024 14:21:06 +0000 Safety of Transportable Motor-Operated Electric Tools - Part 2: Particular Requirements for Planers and Thicknessers
Published By Publication Date Number of Pages
CSA 1999-12-10 41
]]> Scope

This clause of part 1 is applicable except as follows:

1.1 Modification
Replace the first paragraph by:

This International Standard applies to planers and thicknessers with a maximum planing transportable width of 260 mm.None

]]> CAN/CSA-C22.2 NO. 745-4-14-95 (R1999):2000 Edition ?u=/product/publishers/csa/can-csa-c22-2-no-745-4-14-95-r1999/ Tue, 05 Nov 2024 14:19:11 +0000 Safety of Portable Battery-Operated Tools - Part 4: Particular Requirements for Planers
Published By Publication Date Number of Pages
CSA 2000-01-19 24
]]> 1. Scope

This clause of Part 3 is applicable, except as follows:

1.1

Replacement:

The term ""tools"" is replaced by ""planers.

]]> BS 5326:1976 ?u=/product/publishers/bsi/bs-53261976/ Sat, 19 Oct 2024 17:44:29 +0000 Specification. Internal broaching tools and pull chuck locations
Published By Publication Date Number of Pages
BSI 1976 10
]]> This standard specifies a range of nominal shank dimensions for both the pull and tail ends of internal broaches for use on broaching machines, vertical type.

The standard specifies certain dimensions for locating the pull chuck in the pull block of broaching machines, vertical internal type. The constant dimension between the top of the pull block and the platen surface is also given.

The standard is particularly applicable to automatic handling of broaching tools.

Range of nominal shank dimensions for pull and tail ends of internal broaches for use on broaching machines, vertical type, and dimensions for locating the pull chuck in the pull block. Gives constant dimensions between the top of the pull block and the platen surface. Particularly applies to automatic handling of broaching tools.

]]>