🔥🔥 Don’t Miss Out on Our End of Autumn Sale. If you have any questions, feel free to click the bottom right corner to contact our customer service..

Concat us[email protected]
Shopping Cart

No products in the cart.

🔍
BS EN ISO 8098:2023

BS EN ISO 8098:2023

$198.66

Cycles. Safety requirements for bicycles for young children

Published By Publication Date Number of Pages
BSI 2023 54
PDF Format Searchable Printable Preview Now
Guaranteed Safe Checkout
Category:

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

This document specifies safety and performance requirements and test methods for the design, assembly and testing of fully assembled bicycles and sub-assemblies for young children. It also provides guidelines for instructions on the use and care of the bicycles. This document is applicable to bicycles with a maximum saddle height of more than 435 mm and less than 635 mm, propelled by a transmitted drive to the rear wheel. It is not applicable to special bicycles intended for performing stunts (e.g. BMX bicycles). NOTE      For bicycles with a maximum saddle height of 435 mm or less, see national regulations for ride-on toys, and with a maximum saddle height of 635 mm or more, see ISO 4210-1 to ISO 4210-9.

PDF Catalog

PDF Pages PDF Title
2 undefined
4 European foreword
Endorsement notice
7 Foreword
8 Introduction
9 1 Scope
2 Normative references
3 Terms and definitions
11 4 Requirements and test methods
4.1 Brake tests and strength tests — Special requirements
4.1.1 Brake tests to which special requirements apply
4.1.2 Strength tests to which special requirements apply
4.1.3 Numbers and condition of specimens for the strength tests
12 4.1.4 Tolerances
4.1.5 Fatigue test
4.1.6 Plastic material test ambient temperature
4.1.7 Impact test
4.2 Toxicity
13 4.3 Sharp edges
4.4 Security and strength of safety-related fasteners
4.4.1 Security of screws
4.4.2 Minimum failure torque
4.4.3 Quick-release devices
4.4.4 Foot location devices
4.4.5 Folding bicycle mechanism
4.5 Crack detection methods
4.6 Exposed protrusions
14 4.7 Brakes
4.7.1 Braking-systems
4.7.2 Hand-operated brakes
16 4.7.3 Attachment of brake assembly and cable requirements
17 4.7.4 Brake-block and brake-pad assemblies — Security test
4.7.5 Brake adjustment
4.7.6 Back-pedal brake
4.7.7 Braking-system — Strength tests
18 4.7.8 Braking performance
20 4.8 Steering
4.8.1 Handlebar — Dimensions and end fittings
4.8.2 Handlebar grips and end plugs
22 4.8.3 Handlebar-stem — Insertion depth mark or positive stop
4.8.4 Steering stability
4.8.5 Steering assembly — Static strength and security tests
26 4.8.6 Handlebar and stem assembly — Fatigue test
28 4.9 Frames
4.9.1 Frame and front fork assembly — Impact test (falling mass)
29 4.9.2 Frame and front fork assembly — impact test (falling frame)
30 4.10 Front fork
4.10.1 General
4.10.2 Front fork — Bending fatigue test
31 4.11 Wheel and tyre assembly
4.11.1 Wheel and tyre assembly — Rotational accuracy
32 4.11.2 Wheel and tyre assembly — Clearance
33 4.11.3 Wheel and tyre assembly — Static strength test
4.11.4 Wheels — Wheel retention
34 4.11.5 Tyre inflation pressure
4.11.6 Wheel and tyre assembly —Overpressure test
4.12 Pedals and pedal/crank drive system
4.12.1 Pedal tread
35 4.12.2 Pedal clearance
4.12.3 Pedal — Impact test
36 4.12.4 Pedal/pedal-spindle — Dynamic durability test
37 4.12.5 Drive system static strength test
38 4.12.6 Crank assembly — Fatigue tests
39 4.13 Saddles and seat-posts
4.13.1 Limiting dimensions
4.13.2 Seat-post — Insertion-depth mark or positive stop
40 4.13.3 Saddle and seat-post security test
4.13.4 Saddle — Static strength test
41 4.13.5 Saddle and seat-post assembly fatigue test
42 4.14 Chain-wheel and belt-drive protective device
43 4.15 Stabilizers
4.15.1 Mounting and dismounting
4.15.2 Dimensions
44 4.15.3 Vertical load test
4.15.4 Longitudinal load test
45 4.16 Luggage carriers
4.17 Lighting systems and reflectors
4.17.1 Front and rear light
4.17.2 Reflectors
46 4.17.3 Wiring harness
4.18 Warning device
5 Instructions
47 6 Marking
6.1 Requirement
48 6.2 Durability test
6.2.1 Requirement
6.2.2 Test method
49 Annex A (informative) Steering geometry
50 Annex B (informative) Verification of free fall velocity
51 Bibliography

Related products

BS EN ISO 8098:2023
$198.66