Shopping Cart

No products in the cart.

BS EN IEC 61076-3-122:2021 – TC:2022 Edition

$217.84

Tracked Changes. Connectors for electrical and electronic equipment. Product requirements – Detail specification for 8-way, shielded, free and fixed connectors for I/O and data transmission with frequencies up to 500 MHz and current-carrying capacity in industrial environments

Published By Publication Date Number of Pages
BSI 2022 104
Guaranteed Safe Checkout
Categories: ,

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

IEC 61076-3-122:2021 covers 8-way, shielded, free and fixed rectangular connectors for I/O and data transmission with frequencies up to 500 MHz. It is intended to specify the common dimensions, mechanical, electrical and environmental characteristics and tests for this family of connectors. Connectors complying with this document provide an ingress protection level of IP20; however, they are particularly suited for industrial environments with a high level of vibration. There are two classes of connectors defined in this document, indicated by “class A” and “class B” which are distinguished by some electrical and mechanical characteristics to meet the particular sets of requirements of some industrial applications. Class A meets the requirements defined in Ed.1 of this document. With the two classes A and B, the two codings Type I and II, and the two sets of transmission requirements according to the component categories Cat 5 and Cat 6A as defined in ISO/IEC 11801-1, this document specifies 2 × 2 × 2 = 8 variants. All connectors covered by this document feature a current-carrying capacity beyond the minimum requirement of 0,75 A per pin for an ambient temperature of 60° C as defined in ISO/IEC 11801 1. This second edition cancels and replaces the first edition published in 2017. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) Title modified. b) Introduction of two sets of requirements for connectors of “class A” and “class B” where class A matches the requirements defined in the previous edition. c) Definition of new performance requirements for frequencies up to 500 MHz in addition to the performance requirements up to 100 MHz provided with the previous edition. d) Re-structuring to reflect the commonalities of and differences between connector Type I and Type II. e) Revision of drawings to clarify some dimensions. e) The derating diagram has been corrected to align it with the upper limiting temperature in the climatic category, with no reduction of performance for the target applications.

PDF Catalog

PDF Pages PDF Title
1 30453685
65 A-30381155
66 undefined
69 Annex ZA(normative)Normative references to international publicationswith their corresponding European publications
73 English
CONTENTS
75 FOREWORD
77 Figures
Figure 1 – Product overview
78 1 Scope
2 Normative references
80 3 Terms and definitions
4 Mating information
4.1 General
81 Tables
Table 1 – Mating faces of the individual connector styles
82 4.2 Contacts – Mating conditions
4.3 Fixed connectors Type I and II
Figure 2 – Contact interface of a free male connector (right side) mated with a fixed female connector (left side)
83 Figure 3 – Fixed connectors
84 Table 2 – Dimensions for Figure 2 and Figure 3
85 4.4 Free connectors Type I and II
Figure 4 – Free connectors Type I (left) and Type II (right)
86 5 Characteristics
5.1 General
Table 3 – Dimensions for Figure 4
87 5.2 Pin and pair grouping assignment
Figure 5 – Fixed connector pin and pair grouping assignmentfor Type I and Type II, mating face view of connector
Table 4 – Pin and pair assignment for 10/100 Mbps Ethernet
Table 5 – Pin and pair assignment for 1/10 Gbps Ethernet
88 5.3 Classification into climatic category
5.4 Electrical characteristics
5.4.1 Voltage proof
5.4.2 Voltage rating
5.4.3 Creepage and clearance distances
Table 6 – Climatic category
Table 7 – Voltage proof
89 5.4.4 Current-temperature derating
Figure 6 – Connector derating curve
Table 8 – Creepage and clearance distances of the mating interface
90 5.4.5 Insulation resistance
5.5 Mechanical characteristics
5.5.1 Mechanical operation
5.5.2 Insertion and withdrawal forces
5.5.3 Vibration, sinusoidal
5.5.4 Shock
Table 9 – Vibration, sinusoidal
Table 10 – Shock
91 5.6 Transmission performance
5.6.1 General
5.6.2 Insertion loss
5.6.3 Return loss
5.6.4 Near-end cross talk (NEXT)
92 5.6.5 Far-end cross talk (FEXT)
5.6.6 Transverse conversion loss (TCL)
5.6.7 Transverse conversion transfer loss (TCTL)
5.6.8 Transfer impedance
5.6.9 Propagation delay
93 5.6.10 Delay skew
6 Tests and test schedule
6.1 General
6.2 Arrangement for input-to-output resistance test
94 6.3 Arrangement for vibration and shock test (test phase EP1)
Figure 7 – Arrangement for input-to-output resistance test
Figure 8 – Arrangement for vibration test
95 6.4 Test procedures and measuring methods
6.5 Preconditioning
6.6 Test schedules
6.6.1 General
6.6.2 Basic (minimum) test schedule
6.6.3 Full test schedule
96 Table 11 – Test group P
97 Table 12 – Test group AP
98 Table 13 – Test group BP
100 Table 14 – Test group CP
101 Table 15 – Test group DP
Table 16 – Test group EP
102 6.7 Mounting of specimens
Table 17 – Test group FP
103 Bibliography
BS EN IEC 61076-3-122:2021 - TC
$217.84