{"id":419436,"date":"2024-10-20T06:25:54","date_gmt":"2024-10-20T06:25:54","guid":{"rendered":"https:\/\/pdfstandards.shop\/product\/uncategorized\/bs-en-iso-8502-82004-2005-2\/"},"modified":"2024-10-26T12:00:29","modified_gmt":"2024-10-26T12:00:29","slug":"bs-en-iso-8502-82004-2005-2","status":"publish","type":"product","link":"https:\/\/pdfstandards.shop\/product\/publishers\/bsi\/bs-en-iso-8502-82004-2005-2\/","title":{"rendered":"BS EN ISO 8502-8:2004 2005"},"content":{"rendered":"
This part of ISO 8502 describes a field method for the assessment of moisture, usually caused by condensation of water, on steel surfaces prior to application of paint.<\/p>\n
The method can be used on flat and slightly curved horizontal and vertical surfaces. The assessment should not be done on surfaces that are exposed to any falling water, e.g. rain, or condensation.<\/p>\n
The lowest surface moisture (water) level that can be detected by the method is 4 g\/m2.Refinements for considerably lowering this level are indicated in clause 8.<\/p>\n
PDF Pages<\/th>\n | PDF Title<\/th>\n<\/tr>\n | ||||||
---|---|---|---|---|---|---|---|
5<\/td>\n | Preparation of steel substrates before application of paints and related products\ufffd\u2014 Tests for the… <\/td>\n<\/tr>\n | ||||||
7<\/td>\n | Contents Page <\/td>\n<\/tr>\n | ||||||
8<\/td>\n | Foreword <\/td>\n<\/tr>\n | ||||||
9<\/td>\n | Introduction <\/td>\n<\/tr>\n | ||||||
11<\/td>\n | Preparation of steel substrates before application of paints and related products\ufffd\u2014 Tests for the… 1\ufffd\ufffd\ufffd Scope 2\ufffd\ufffd\ufffd Normative references 3\ufffd\ufffd\ufffd Principle 4\ufffd\ufffd\ufffd Reagents 4.1\ufffd\ufffd\ufffd Water 4.2\ufffd\ufffd\ufffd Monoethylene glycol <\/td>\n<\/tr>\n | ||||||
12<\/td>\n | 5\ufffd\ufffd\ufffd Apparatus 5.1\ufffd\ufffd\ufffd Glass bottle 5.2\ufffd\ufffd\ufffd Adhesive patch 5.3\ufffd\ufffd\ufffd Magnetic panel 5.4\ufffd\ufffd\ufffd Plastic brush 5.5\ufffd\ufffd\ufffd Graduated syringe 5.6\ufffd\ufffd\ufffd Handheld refractometer 6\ufffd\ufffd\ufffd Procedure 6.1\ufffd\ufffd\ufffd Preparation of sampling area 6.1.1\ufffd\ufffd\ufffd A zone on the steel surface shall first be selected by the parties interested in the test. 6.1.2\ufffd\ufffd\ufffd Place the magnetic panel ( 6.1.3\ufffd\ufffd\ufffd Clean an area approximately 6.1.4\ufffd\ufffd\ufffd Remove the magnetic panel. 6.1.5\ufffd\ufffd\ufffd Remove the protective cover and the central punch-out from the patch. 6.1.6\ufffd\ufffd\ufffd Press the adhesive patch against the steel surface so that the compartment in the patch … <\/td>\n<\/tr>\n | ||||||
13<\/td>\n | 6.2\ufffd\ufffd\ufffd Preparation of solvent 6.3\ufffd\ufffd\ufffd Preparation of refractometer 6.4\ufffd\ufffd\ufffd Removal of moisture (water) from the steel surface 6.5\ufffd\ufffd\ufffd Refractometric measurements 7\ufffd\ufffd\ufffd Expression of results <\/td>\n<\/tr>\n | ||||||
14<\/td>\n | 8\ufffd\ufffd\ufffd Precision <\/td>\n<\/tr>\n | ||||||
16<\/td>\n | 9\ufffd\ufffd\ufffd Test report <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" Preparation of steel substrates before application of paints and related products. Tests for the assessment of surface cleanliness – Field method for the refractometric determination of moisture<\/b><\/p>\n |